Can I Install a Bath Tub Myself? Considerations And Actions
Can I Install a Bath Tub Myself? Considerations And Actions
Blog Article
The article listed below about How to Install a Bathtub Yourself is absolutely captivating. Don't skip it.
Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a moderately difficult project. If the old tub is readily accessible, the job can move quickly; if you have to open up a wall surface to get rid of the old bathtub as well as position the new tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task as well as are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed task, it is better to take into consideration using one before you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have already bought a brand-new tub and do not need to change the setup of your previous water system pipelines.
Your tools and product list must comprise the following:
Getting ready for the Installation
First of all, the supporting framework supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you should do is detach the water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the tub up until the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the supply of water and examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the tub has actually been utilized at least when as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet and the sink. Safeguard the tap in position with the producer offered backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type needs to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not take into account this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles using water-resistant or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry about Tools You Need to Install a New Bathtub while doing a search on the web. Sharing is good. Helping people is fun. I am grateful for your time. Visit us again soon.
Visit My Website
Report this page